Let’s get shaking. HAMILTON HEATER SHAKER INSTALLATION INSTRUCTIONS FOR PREP
Hamilton Heater Shaker Installation Instructions
Please start your Hamilton Heater Shaker (HHS) installation at the section that best suits your installation status.
Section 1: Installing an HHS on a New Prep.............................. 4
Section 2: Upgrading an Existing Prep with an HHS............... 10
Section 3: Prep Support.......................................................... 18
SECTION 1:
INSTALLING AN HHS ON A NEW PREP
Unpack and begin installing the Prep, following the instructions in the Prep Welcome Packet (A). The instructions will indicate to install the HHS at Step 22 ; return to these instructions at that point. 1
A
4
Place the HHS in the back- left corner of the deck area. 2
5
SECTION 1: INSTALLING AN HHS ON A NEW PREP
Attach the HHS to the Prep using a 3 mm hex wrench and one of the included screws. The Prep comes with a set of hex wrenches for installation and maintenance. 3
6
Secure the power/ communication cable using the cable bracket and included screw. 4
7
SECTION 1: INSTALLING AN HHS ON A NEW PREP
Unscrew the accessory port cover and screw in the HHS cable. Make sure the cable is attached tightly. 5
8
Resume installing the Prep, starting with installing the deck, at Step 23 in the Prep Welcome Packet (A). 6
A
9
SECTION 2: UPGRADING AN EXISTING PREP WITH AN HHS
Power off the Prep and disconnect it from power. If an HHS is connected while the Prep is on, the Prep or HHS could be damaged. 1
10
Remove the 8-site deck and set it aside. Store the old deck in a safe location. 2
11
SECTION 2: UPGRADING AN EXISTING PREP WITH AN HHS
Place the HHS in the back- left corner of the deck area. 3
12
Attach the HHS to the Prep using a 3 mm hex wrench and one of the included screws. The Prep comes with a set of hex wrenches for installation and maintenance. 4
13
SECTION 2: UPGRADING AN EXISTING PREP WITH AN HHS
Secure the power/ communication cable using the cable bracket and included screw. 5
14
Unscrew the accessory port cover and screw in the HHS cable. Make sure the cable is attached tightly. 6
15
SECTION 2: UPGRADING AN EXISTING PREP WITH AN HHS
7
Install the 7-site deck:
A. R emove the deck and base plates
from their packaging.
B. P lace the deck frame on the Prep. The sites numbered 4 and 8 should be at the front. C. Install the base plates for each site. Press down on each plate to make sure it is secure.
4 8
16
8
D
Plug in the Prep, power it on, and confirm that the HHS is connected:
A. Sign in, if prompted.
B. Tap New Protocol.
C. Select either Detect or Add on the Place Labware page. D. C onfirm that site 1, the back-left site, is grayed out and says
“HHS.” If the HHS does not appear, contact Hamilton support.
17
SECTION 3: SUPPORT
Hamilton is here to help. Browse our on-line help center or file a ticket to ask a question. For help, visit us at HamiltonCompany.com/prephelp .
18
19
©2019 Hamilton Company. All rights reserved. All other trademarks are owned and/or registered by Hamilton Company in the U.S. and/or other countries. Lit. No. BR-1912-121 v1.0 — 12/2019
United States +1-775-858-3000 United Kingdom, Ireland +44 (0) 121 272 92 80 Brazil +55 (11) 126 50562 China +86 21 6164 6567 France +33 184 008 420 Italy +39 39 689 33 93
Japan +81 3 6435 6850 Spain, Portugal +34 930 186 262 Denmark, Norway, Sweden, Finland +46 (0) 8 410 273 73 Germany, Switzerland, Austria, Benelux +49 (089) 248 804 808
To find a subsidiary or distributor in your area, please visit, www.hamiltoncompany.com/contacts.
Web: www.hamiltoncompany.com/robotics Email: marketingrequest@hamiltoncompany.com
Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 20Powered by FlippingBook